Alarm Lock ETPLN Betriebsanweisung PDF herunterladen (Seite 28)

28 DL-WINDOWS™ for Trilogy Networx™ V4.0 USER'S GUIDE

After the discovered physical lock(s) are assigned to the

selected Gateway and Use Selected Locks is clicked, the

system requests if you wish to "Link" the discovered physical

locks to a "virtual lock" Profile. Click Yes to proceed or click No

to exit without linking.

Link Locks (Popup)

The "Discovered Locks" popup displays the search results.

In the example shown above, the popup screen entitled

"Discovered 1 Locks" appears, indicating the serial number

of the lock(s), the signal strength and the lock model(s). Note:

The number displayed in the title bar will reflect the number of

discovered locks.

To assign the discovered physical lock(s) to the selected

Gateway, click the check box next to each lock and click Use

Selected Locks; to exit without assigning, click Cancel.

down list. The Gateway selected will transmit the discovery

request radio signal to the locks in the vicinity. Only those locks

within range that have not already been configured will

respond.

Note: The maximum search time allowed for each discovery

request is 1 minute. To minimize the search waiting time, this

screen allows you to limit the search to a certain quantity of

installed locks. In addition, you can manually stop the

discovery process at any time by pressing the Esc key on the

keyboard. If you know the number of installed locks to be

discovered, select that number and the discovery process will

stop the moment that number of locks are found. If the number

of locks selected exceeds the actual number physically

installed, the discovery process will continue for either a

maximum of 1 minute or until the Esc key is pressed.

Example: If the number selected is 10, but in fact only 8 locks

exist, the system may find all 8 locks, but will keep searching for

10 until the one minute timeout duration expires--or until the

Esc key is pressed.

Click the Discover Locks On Selected Gateway button to

initiate the search.

Lock Configuration Error (Popup)

This popup appears if the connection between DL-Windows

and the Gateway is lost or is not working properly. Click Yes

to attempt to reconnect to the specified Gateway.

Lost Gateways (Popup)

This popup appears after a failed attempt to assign

discovered physical locks to a Gateway.

As detailed previously, the Gateway Configuration screen

allows you to discover physical locks and assign them to a

specific Gateway (click the Discover Locks On Selected

Gateway button). The "Discovered Locks" popup appears

and lock(s) you wish to assign to the Gateway are selected.

When the Use Selected Locks button is clicked, the Gateway

sends "configuration data" to the selected locks. This

"configuration data" contains items (an internal lock

designation, a specific radio channel and security data) all

embedded in what is referred to as the "Lock Table". This

"configuration data" instructs the physical lock(s) to

communicate ONLY with that Gateway and prevents other

Gateways from communicating with the lock(s).

If after several attempts to communicate with the lock(s), the

Gateway still does not receive confirmation that this

"configuration data" was received from the selected lock(s)

successfully, this popup appears. In short, the Gateway was

unable to "configure" the selected physical locks, and thus

was unable to assign the selected physical locks to the

Gateway.

This popup appears if you attempt to use a selected lock in

the "Discovered Locks" popup that already exists in the Lock

Table of the selected Gateway. Click OK to attempt to

reconfigure by re-sending the "Lock Config Table" to the

selected Gateway.

Lock already exists (Popup)

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

Alarm Lock ETPLN Betriebsanweisung Seite 28

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Alarm Lock ETPLN