Alarm Lock DL1300 Bedienerhandbuch PDF herunterladen (Seite 9)

Programming Functions (cont'd)

Disable All: If Master Code is used, disables all 100 User\Manager Codes and clears all 3 Service Codes. If

a Manager Code is used, disables all Users (even across multiple Banks) under that Manager.

Disable Users Only: If Master Code is used, disables all 90 Users and clears all 3 Service Codes, while Manag-

ers remain active. If a Manager Code is used, disables all Users (even across multiple banks) under that Man-

ager.

Enable All: If Master Code is used, re-enables all 100 User/Manager Codes (Service Codes must be re-

programmed). If a Manager Code is used, re-enables all Users (even across multiple Banks) under that Man-

ager. Note: Managers cannot disable themselves. Use Function 944 to restore Functions 955 and 950. In

addition, if Codes are disabled using Function 955 or 950, and a new User Code is subsequently added (or an

existing Code changed), the new (or changed) User Code will automatically become enabled.

Enable/Disable All

Disable All

[ __ __ __ __ __ ] ;955;

Master/Manager Code**

Enable All

[ __ __ __ __ __ ] ;944;

Master/Manager Code**

[ __ __ __ __ __ ] ;950;

Master/Manager Code**

Disable Users Only

Next Free Code Address Locator ; 7 ;

Using the same method of beeps and flashes used in the Code Location Function, and dependent on the Mas-

ter or Managers Code entered, the lock will report the next available address for User Access Code program-

ming.

Report Sequence

1. At the start of the Next Free Code Location function, the lock will Flash both the GREEN and RED LEDs and will emit a low tone.

2. The lock will identify the Bank number by flashing the GREEN LED and beeping the sounder from 0 -9 times.

3. To signify the end of the Bank number ID sequence, the lock will flash both the GREEN and RED LEDs and will emit a low tone.

4. The lock will identify the User number by flashing the GREEN LED and beeping the sounder from 0-9 times.

5. To signify the end of the Code Location function, the lock will flash both the GREEN and RED LEDs and will emit a low tone. If no free

address is found, then the lock will emit a programming error tone sequence. No LED flashes/sounder beeps represent the number

zero.

Be sure to record all Code locations in the blank worksheet (page 4) for future reference. If the location of a Code is

not known, use this function to find the Code. The lock will identify the BANK (0-9) and USER (0-9) by beeping and

flashing the GREEN LED 0 to 9 times as detailed below.

Code Location Function ; 6 ;

[ __ __ __ __ __ ] ; 6 ; [ __ __ __ __ __ ]

Master/Manager Code** Code 2 - 5 digits

If the code entered is recognized, the following sequence will occur:

1. At the start of the Code Location sequence, the lock will Flash both the GREEN and RED LEDs and will emit a low tone.

2. The lock will identify the Bank number by flashing the GREEN LED and beeping the sounder from 0 -9 times.

3. To signify the end of the Bank number ID sequence, the lock will flash both the GREEN and RED LEDs and will emit a low tone.

4. The lock will identify the User number by flashing the GREEN LED and beeping the sounder from 0-9 times.

5. To signify the end of the Code Location function, the lock will flash both the GREEN and RED LEDs and will emit a low tone.

Note: Should the Code not be recognized, the lock will sound 5 beeps with a RED LED. When the Bank and/or slot numbers are

zero, the GREEN LED will not flash and the sounder will not beep.

** Required only if DL1200 is locked.

[ __ __ __ __ __ ] ; 7 ;

Master/Manager Code**

1 2 3 4 5 6 7 8 9 10 11 12 13

Kommentare zu diesen Handbüchern

Keine Kommentare

Alarm Lock DL1300 Bedienerhandbuch Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Alarm Lock DL1300